Haynie Boats..Talk to me

["W"]

Im looking at the 20foot or 21 foot does anyone around here have one? I would like some info before I drive to Texas!!

How much does the 24ft cost?

[LaAngler]

the Z21 would be my choice for big lake not those flats models

[Deadly D]

the Z21 would be my choice for big lake not those flats models
Bruce W has to have low sides to sling them 12" trout or did you forget:*****::*****:

[Jay]

Now your talking that boat is made right down the road from my coast house.....If you want I will PM you the number for the owner, he is now my site sponsor and one bad
a s s dude.

["W"]

the Z21 would be my choice for big lake not those flats models

From what I was reading those flats can handle some good chop.....What you think Jay??

[Hopedale Hustler]

yaa them flat models take an azz whuppin....i know a guy very well that has one and frum what i hear he shoulda got that blackjack he wanted...if i had the money..thats the way id go..either a blackjack..or that yellowfin 24 bay..

["W"]

yaa them flat models take an azz whuppin....i know a guy very well that has one and frum what i hear he shoulda got that blackjack he wanted...if i had the money..thats the way id go..either a blackjack..or that yellowfin 24 bay..


Yellowfin 24ft is about 70,000 That's OUT!!!!:D

[speckdaddy]

nice boats w, with the jack plate and the optional tunnel hull, ya can take off in well, about 2-3 inches o wawduh

[speckdaddy]

Yellowfin 24ft is about 70,000 That's OUT!!!!:D
hey dubya, not tryin ta jack ya thread but did ya ever look at the hewes line of boats? sweet boats for a reasonable price,located in florida:)

[flounder_smacker]

hewes are sweet. i have an 18 redfisher and run vbay all the time and dont get wet and with the tabs the ride isnt bad for a 18ft boat.

[Hopedale Hustler]

Yellowfin 24ft is about 70,000 That's OUT!!!!:D

yaaa uuu rigght...

[LaAngler]

W as much as you like to fish with bigger groups of people why not get a 22 or 24?

you got enough truck to pull it

[huntin fool]

W as much as you like to fish with bigger groups of people why not get a 22 or 24?

you got enough truck to pull it



he aint got enuf truck to pull it! he got a dang chevy, he needs a ford..but i dont think ford makes trucks low enuf to the ground for him..:*****:

["W"]

W as much as you like to fish with bigger groups of people why not get a 22 or 24?

you got enough truck to pull it


Im sure I will get a 22ft......Just dont like hauling that thing!!!! Hard or a trailer putting as many miles as I do

[Jay]

he aint got enuf truck to pull it! he got a dang chevy, he needs a ford..but i dont think ford makes trucks low enuf to the ground for him..:*****:


That ain't right :rotfl::shaking::rotfl:

[Deadly D]

he aint got enuf truck to pull it! he got a dang chevy, he needs a ford..but i dont think ford makes trucks low enuf to the ground for him..:*****:
Fool you better watch it you might have to get a new fishing buddy. Oh well you probably be better off:*****:

[Reel Bender]

he aint got enuf truck to pull it! he got a dang chevy, he needs a ford..but i dont think ford makes trucks low enuf to the ground for him..:*****:

LMAO. Good one Fool!!

[Reel Bender]

W as much as you like to fish with bigger groups of people why not get a 22 or 24?

you got enough truck to pull it

Shhot that be a Houseboat for a guy like him, heck he could live on something that big!:D

[FlatoutFishin]

Capt Aubrey Black fishes a Haynie down in Baffin...nice boat, good choice.

[Reel Bender]

Capt Aubrey Black fishes a Haynie down in Baffin...nice boat, good choice.


He'd probably give some good input, it gets pretty rough down there at times!

[Salty]

I fished out of a 22' HO back in April in Corpus. Dood will geaux skinny.

Ryan...Jay...Bender...any of you guys got an update on McBride?

[FlatoutFishin]

He'd probably give some good input, it gets pretty rough down there at times!

Above and below the waterline! Believe he's had a few lower unit problems.

[huntin fool]

LMAO. Good one Fool!!


i figured you texans would like that..



W what size motor you gunna get??

[Salty]

i figured you texans would like that..



W what size motor you gunna get??



He's gonna put the 30 off the 1200cc on it. :)

["W"]

i figured you texans would like that..



W what size motor you gunna get??


Don't worry you want see it!!!:eek:

[huntin fool]

Don't worry you want see it!!!:eek:


will it be going so fast i cant see it, or i cant see you over the sides??


j/king ofcourse. :grinpimp:

[cordgrass]

will it be going so fast i cant see it, or i cant see you over the sides??


j/king ofcourse. :grinpimp:


dang fool, hitting w hard. what happened.

[Reel Bender]

I fished out of a 22' HO back in April in Corpus. Dood will geaux skinny.

Ryan...Jay...Bender...any of you guys got an update on McBride?


He posted this on www.2coolfishing.com (http://www.2coolfishing.com) on july 6th.

Thanks for asking guys, and yes, rumors of my demise are highly exaggerated. I know I should have checked in a lot sooner, but the 'no spin' truth is that I sorta tucked tail into a little reclusive funk here lately. Not saying I'm a racehorse or anything, but when you're used to running with the herd everyday, and then all of a sudden find yourself hobbled down and looking at the glue factory, well, you might just want to hunker down in your stall a while too. Well I did.

Foot IS getting better, but man that's going to be one ugly appendage when this is all over. I may have to buy some pink crocks to cover it up. Still have a lot of meat to grow back yet, and there are still some tendons and veins exposed so have to be careful. Was going back to the hospital every day but think I can handle it now....or at least am going to try. It was an hour in, then 3 or 4 hours there, plus an hour back each day which made you totally worthless. I can stand, walk a bit and sit for a while, but not for very long before it gets angry again and then I have to find a prop up hole for a few hours. A good night's sleep just ain't gonna happen and we all might forget how many nerves a foot has in it. A bunch of them are apparently growing back now and they are all fighting for attention, especially when you're supposed to be counting sheep and not lightning bolts up your foot. By the way, Vicodin is not a good thing, does not help anything, and only tends to make you stupid and makes the world revolve around the couch. That Rx strength Ibuprofen rocks though and sure helps knock the swelling back down. Good stuff.

Anyway, enough whining already. It's going to be O.K. and am shooting for getting wet the 1st of October. Capt. Tricia is still knocking the fire out of some great fish but I think is trying to kill herself trying to do it all, both on the water and at the house. Tough (rough lol) girl.

If I could say anything, it would be that the entire world has a lot to learn from the people at 2Cool. This site was appropriately named. It's about people helping each other, whether it's a question about an air conditioner, a lure, a spot, or even about one of us getting into a bind. The response Tricia & I received on the benefit auction was overwhelming and there are no words worthy enough to express our humble gratitude. I just hope one day I can be the man my dog thinks I am, and I certainly hope I can give back to the people even here a fraction of the blessings we've received.

Thanks to everybody again, but the main thing is let's learn from this and shoot for nobody else getting hurt. The stable is no place you want to be...trust me, so wear those darn guards and keep your wounds covered. To think we're bullet proof is machisimo at it's dumbest. Y'all leave a few out there for me...will ya lol?

(ps. No I didn't run spell check. That stupid Vicodin told me it didn't matter)

end







Man those Stingrays can jack you up!!!!!!!

[huntin fool]

dang fool, hitting w hard. what happened.


just messing with him! aint messed with him in awhile..:spineyes:

[Salty]

He posted this on www.2coolfishing.com (http://www.2coolfishing.com) on july 6th.


Thanks, Bender.

["W"]

Thanks, Bender.

Here we GO:rolleyes:

[Jay]

I found your boat "W" (http://www.chrismarineboats.com/NewBoat_09HAYNIE_Z21_LONHORN-O21007.html)


http://www.chrismarineboats.com/DSCN3667A.JPG (http://www.chrismarineboats.com/NewBoat_09HAYNIE_Z21_LONHORN-O21007.html) New 2009 HAYNIE - Z 21 (http://www.chrismarineboats.com/NewBoat_09HAYNIE_Z21_LONHORN-O21007.html) STK# O21007

[Big Kahunaz]

W....did you see on the site what they use in the stringer system of this boat?...
I think I saw wood! Might want to further investigate.

[LaAngler]

looks like some treated plywood for some of the decks and boxes, then sealed in glass....

[Salty]

Why would somebody want this type boat to fish Big lake? :confused:

[Big Kahunaz]

exactly...get that Frontier, Triton, or better yet....BlackJack!!! Someone has a 24ft kenner in the classifieds section...I'd buy that and drop a new motor on it and you'll have pretty much the best dam boat ever made..IMO!

[Capt. Ryan Rachunek]

Im looking at the 20foot or 21 foot does anyone around here have one? I would like some info before I drive to Texas!!

How much does the 24ft cost?

Stay in LA, Haynie doesn't take FEMA cards.........

[Big Kahunaz]

Stay in LA, Haynie doesn't take FEMA cards.........

ARE you sure?:confused:

[Salty]

Stay in LA, Haynie doesn't take FEMA cards.........

:spineyes:

[fishinpox]

http://www.glasstream.com/228.php check these out w !!!!!!!!!!!

[Reel Bender]

I think he got the link wrong try this

http://www.glasstream.com/amanda.php

[LaAngler]

http://www.glasstream.com/228.php check these out w !!!!!!!!!!!


the wrap on the 36 is sick

["W"]

Stay in LA, Haynie doesn't take FEMA cards.........

They said FEMA expired but they are taking Stimulus checks:eek:

[fishinpox]

the wrap on the 36 is sick
some may call it sick other may call it obamaed out!!!

[LaAngler]

this is what i imagine heaven looks like....

[huntin fool]

this is what i imagine heaven looks like....


thats what my boat looks like every weekend bruce!

["W"]

You want to see sick....Just wait...Im going to but a saltycajun.com wrap........

[LaAngler]

thats what my boat looks like every weekend bruce!


yeah with 14 year olds....;)

[bigdog]

this is what i imagine heaven looks like....

If that is heaven, I would walk cross water to get there.:grinpimp:

[LaAngler]

LMAO yea U right

["W"]

thats what my boat looks like every weekend bruce!

13year olds.......... He said he had the hots for Austins cousin.... :p

[huntin fool]

13 years old.......... He said he had the hots for Austins cousin.... :p



nooo..atleast i dont sit there and check the girls out that come to my wharf like you do :p


are you doubting my good looks? W have you seen what comes to my wharf sometimes????

[Deadly D]

nooo..atleast i dont sit there and check the girls out that come to my wharf like you do :p


are you doubting my good looks? W have you seen what comes to my wharf sometimes????
he got you on that one W:*****::*****:you sick puppy

[LaAngler]

it's the wharf fool

[huntin fool]

it's the wharf fool


its my good looks, and my boat.



anyways, W you never answered what size motor you getting?

[fishinpox]

this is what i imagine heaven looks like....
im gonna have to agree my friend!!

[Red Devil]

its my good looks, and my boat.



anyways, W you never answered what size motor you getting?
a trolling motor fool

["W"]

its my good looks, and my boat.



anyways, W you never answered what size motor you getting?

Biggest they will put on a 22ft....It will be a YammaHammer 4 stroke for SHO...

[cmdrost]

24 HO or the z21 models are great for big lake. Don't let the short sides scare you off. Great boat and super fast and great in a chop.

["W"]

I think this is what I'm going to buy with a 200 Yamaha 4 stroke.... 36 volt 101 trust great white trolling motor!!!! should be set up for 10 years with this boat!!!

[cmdrost]

just my opinion, but everyone I've talked to said the yamaha 200 4 stroke isn't a great motor. Thats why I went with the 150 4 stroke on my frontier. @00 is much heavier with not much better performance. Now that boat with the 200 HPDI would move! I wish I had put that engine on my frontier!

But I promise you will not be disappointed with that boat.

["W"]

just my opinion, but everyone I've talked to said the yamaha 200 4 stroke isn't a great motor. Thats why I went with the 150 4 stroke on my frontier. @00 is much heavier with not much better performance. Now that boat with the 200 HPDI would move! I wish I had put that engine on my frontier!

But I promise you will not be disappointed with that boat.


Its rated for a 225 you think that 150 would handle...

[cmdrost]

150 would push it good. I cruise at about 36 and top out around 50 with me and one person.

Chris at Haynie is a Mercury dealer. I'd put the 200 or 225 optimax on it!

[all star rod]

CMDROST, I agree with you. The Yamaha 200 4 stroke is almost 100 pounds heavier than the HDPI 2 stroke. The 150 4 stroke and 200 HPDI have basically the same weight. I really do not see too many 200 4 strokes on the water but I see a lot of 225 and 250.

[LaAngler]

225 opti on the Z21 no doubt

boat is designed with a pad for a lighter stronger motor to lift it up

[all star rod]

If you are going to go with a 2 stroke I would go with the YAMAHA 200 HPDI over any MERC. However if I would ever get a Merc I would get the Optimax.

[Jay]

I would put the 225 optimax for sure.

[Natural Light Kid]

i'm going to show my ignorance. i never heard of haynie until this thread started. what makes them so special compared to the others (pathfinder, champion, etc.)? how are they priced compared to the others too?

["W"]

i'm going to show my ignorance. i never heard of haynie until this thread started. what makes them so special compared to the others (pathfinder, champion, etc.)? how are they priced compared to the others too?

Change your avatar and we might tell yea:rolleyes:

[Reel Bender]

i'm going to show my ignorance. i never heard of haynie until this thread started. what makes them so special compared to the others (pathfinder, champion, etc.)? how are they priced compared to the others too?

The same reason tha makes everything else he uses good!!!!!
It's Texas Made!!!!!!!!!!!!!!!!!!!:work:

[Deadly D]

I would put the 225 optimax for sure.
Jay I agree with you on the opitimax. Better hole shot cause more low end torque and fuel mileage is close on cruise speed but not quiet as good on full throttle.

[FlatoutFishin]

Screw the Haynie....I think you need an SCB! :smokin:

[all star rod]

Natural good question...I am not sure how much they run in price!! Does anyone know??

[Reel Bender]

Screw the Haynie....I think you need an SCB! :smokin:

Small Can Boat?

That be a Pirot would 'nt it?

[FlatoutFishin]

Small Can Boat?

That be a Pirot would 'nt it?

You mean "short coonazz boat" as in pirot.

["W"]

Screw the Haynie....I think you need an SCB! :smokin:

don't think so!!!

[FlatoutFishin]

don't think so!!!

How you gonna keep up?

[Reel Bender]

You mean "short coonazz boat" as in pirot.

There was supposed to be a j +u in there!

[all star rod]

W why you not getting another SEA FOX???????????????????????
Salty I guess we all know what the best boat on the market is now. Once a motor is picked out then we will all know what the best motor will be!

[Salty]

W why you not getting another SEA FOX???????????????????????
Salty I guess we all know what the best boat on the market is now. Once a motor is picked out then we will all know what the best motor will be!


So far...it's a known fact that:

Sea Fox is the "best"
MotorGuide is the "best"
Waterloo is the "best"
Curado is the "best"
Sand Eel is the "best"
Big Game is the "best"
Chevy is the "best"


If you don't have these.........YOU SUCK!!!

[LaAngler]

you'll have to source the sea fox claim, i don't remember that one...

[all star rod]

LaAngler that one may have a DISCLAIMER!!:*****::*****:

[Salty]

you'll have to source the sea fox claim, i don't remember that one...


He has one so it's the "best".

You should know...you were the author of "1200cc Sea Fox".

[LaAngler]

no that was ryan and you

[LaAngler]

z21 w/opti

[cmdrost]

that boat just looks fast!

["W"]

If everything goes right I will get the Z21 just not sold in that merc yet?? I don't need speed I just want a good boat with room to fish 3 and take chop good!!!

[cmdrost]

speed is good for long runs in the ship channel. Yamaha f150 is good motor, but I think you might be wishing for more power once settled into it.

[LaAngler]

speed is good for long runs in the ship channel. Yamaha f150 is good motor, but I think you might be wishing for more power once settled into it.


without a doubt, a 200 or 225 will get you a lot better cruise speed not to mention top end. Plus it doesn't have to work as hard as a 150 which will improve mileage. A pad boat like that will not perform right without enough horsepower to lift the nose up.

in some of the pictures i saw some plastic lids and plastic cleats, not sure why they wouldn't just use glass lids and stainless.

one thing about the speckle paint finish inside is that it's much easier to keep looking clean

[all star rod]

If you are looking at getting a Yamaha go on their web site and look at the test data they have done on boats. Maybe yours was not tested but I am sure you can find one that is pretty close to the weight and hull design of the one you are looking at(Haynie). Hard to believe that boat has a weight of 1,350# and rated for a 250hp. The test results/data that Yamaha did with the 4 stroke 150/Xpress X22Bay are pretty dang accurate compared to the way mine runs....fuel ecomony, top speed, speed @ rpms, and plane time. If anything the test data is conservative based on the load weight during the test. I usually have more weight in my boat since I fish three 90% of the time. Also, a 4 stoke can run at higher RPMS than a 2 stroke DI motor. I bet the Optimax has the same range as the HPDI...5,500 rpms compared to a 4 stoke at 6,000 RPMS. I bet that boat would fly with a 225 Optimax!
I think the 150 Yamaha 4 stoke is more than enough motor for that boat...get a jack plate.

[Hopedale Hustler]

it looks like a POS mako.

[Deadly D]

Allways get what the boat is rated for. The boat performs the best with that rating. It dont mean you have to run it in the corner all the time but if you need it you got it. Under rating a boat is hard work on the motor most of the time. Not talking about all boats but hulls 19' and up.

[all star rod]

Nothing wrong with putting the MAX H.P...but do you really need it... One question 80-90% of 24' bay boat are rated for a 300H.P. motor....how many do you see with a 300H.P. on the back (10%-20%)?????? Most have 225H.P. or 250H.P. To me if the motor can run at least 50mph and get out of the hole quick with a load then good enough for me...but to each his own. I my case I went with a 150 4 stroke over a 200 HPDI....the HPDI was 6 mph faster...but running at 40mph the gas mileage was basically the same....and I wanted a 4 stroke.

[Deadly D]

Nothing wrong with putting the MAX H.P...but do you really need it... One question 80-90% of 24' bay boat are rated for a 300H.P. motor....how many do you see with a 300H.P. on the back (10%-20%)?????? Most have 225H.P. or 250H.P.
I only know 4 that are rated for 300 and they all have 300. Iknow some that are rated for 275 and only have 250 nad they are optimas

[all star rod]

4??? Look at these 24' bay boats manufacutres on their web site I bet you they have a 300H.P. max rating: Triton LTS, Natuic Star, Blazer Bay, Sea Pro, Ranger, Champion, Scout, Skeeter, Shearwater, Blue Wave, Hydra-Sports and so on....most 24' bay boat companies rate them for a 300H.P....OK so if they are rated for a 250 and the have a 225 then are the under powered??? I would be you that most have a 225 or 250HP on their boat. I bet you $100 if you look at 10 24' bay boat rated for a 300HP 7-8 have a 225 or 250HP on the back. Heck I know 3 guides out of Dularge that have 24' blazer bay boat (rated for a 300) and they have 225 or 250 on the back. Again, nothing wrong with going with the max H.P. but I would give up HP to get the motor I wanted as long as the boat still ran @ 50 and got out of the hole quick with a load.

[Deadly D]

4??? Look at these 24' bay boats manufacutres on their web site I bet you they have a 300H.P. max rating: Triton LTS, Natuic Star, Blazer Bay, Sea Pro, Ranger, Champion, Scout, Skeeter, Shearwater, Blue Wave, Hydra-Sports and so on....most 24' bay boat companies rate them for a 300H.P....OK so if they are rated for a 250 and the have a 225 then are the under powered??? I would be you that most have a 225 or 250HP on their boat.
well you are correct to some degree but horsepower ratings on most of them are from 200-300 and 250-300 so testing complies with that.

[all star rod]

Well if a 24' has a HP range of 100HP then why don't a 22' boat have that range. It is all a marketing thing. Most boat makers do not want to price themselves out. Most can still afford a 22' with a 200 or 225 with Max HP. Think about it.

[LaAngler]

bottom line is that this boat with a light fishing load should do close to 50 with a 150, it would do north of 60 with a 2 1/4 propped right

that's a lot

[all star rod]

My Xpress X22 Bay boat which has a dry weight of 1,700# compared to this boat of 1,350# does right at 50mph....48/49 @ 5,900rpms (I have a 6" jack plate) with 3 men in the boat, 44 gallons of fuel plus a 152qt ice chest, fishing tackle, three batteries plus the other crap you carry....This boat with a 150 should easliy do 50mph loaded. I know this I would rather have a little less speed and have a 4 stroke Yamaha 150 then a Merc Optimax 200/225. Also, how many times are you able to run a bay boat at 60 plus MPH....this is not bass fishing...

[Hopedale Hustler]

just get a yellow fin 24 bay..slap that new 350 yammy on the back...be done with it..

[all star rod]

Big suprise....a 24' bay boat rated for more than a 250HP....:rotfl:.....I guess we can add another one to the list.

That is one fine boat there!

[huntin fool]

just get a yellow fin 24 bay..slap that new 350 yammy on the back...be done with it..


WOW :eek:

[Capt. Ryan Rachunek]

Has Reddy ever owned a boat with triple digit power????

BTW - Those 350 Yammies sound like the lower unit is going to fall off everytime you engage the gears.... And the steering on them whines like an alleycat.....

[FREON]

Has Reddy ever owned a boat with triple digit power????
sure he has...I heard his next to last boat had 9 1/2 hp....:rotfl::*****::rotfl::*****::rotfl:

["W"]

I got the itch bad.............

[Hopedale Hustler]

Has Reddy ever owned a boat with triple digit power????

BTW - Those 350 Yammies sound like the lower unit is going to fall off everytime you engage the gears.... And the steering on them whines like an alleycat.....


sure it wasnt just the one you heard....my cousin runs one on back of his yellowfin in venice..and that thing is sweeeett...

just not on gas so much..

[J.D.L]

I'm very suprised that the pictured Haynie has plastic cleats. Whats with that?

[redspeck82]

I have no clue? But i was wondering what makes these boat so good i can see the hull looks very nice but is the ride unbeliveable are what? just wondering?

["W"]

#1 I want a boat no body on our lake has....only seen one so far...#2 I heard that are smooth riding boats and take a good chop.....#3 I like the deck lay out!!! Short guy sides

[huntin fool]

#1 I want a boat no body on our lake has....only seen one so far...#2 I heard that are smooth riding boats and take a good chop.....#3 I like the deck lay out!!! Short guy sides



you gunna get a power pole too??

[Ray]

I'm very suprised that the pictured Haynie has plastic cleats. Whats with that?

No grab rail. I cannot do without a grab rail over the wind shield.

[Reel Bender]

No grab rail. I cannot do without a grab rail over the wind shield.

If you are not tall enuff to grab it......................it does'nt make a whole lot of difference!!!!;)

["W"]

This pic is stripped down you add what you want!! Custom build your own!!!

[Ray]

Where do you keep the croakers?????

[Reel Bender]

Center Hatch in back, notice the SS intake Screen bootom center of hull.

[Ray]

I was jerkin' "W"s chain.

[Reel Bender]

I was jerkin' "W"s chain.

I know;)

So was I!!:D

[all star rod]

What does this boat cost for example with a 150 4 stroke Yamaha...ready to fish. I am sure the troll motor is extra...80# thrust plus GPS/Fishfinder.

["W"]

What does this boat cost for example with a 150 4 stroke Yamaha...ready to fish. I am sure the troll motor is extra...80# thrust plus GPS/Fishfinder.

Will have a price tomorrow...loaded out with a 225 Opti max 101 Great white 36volt with Lowrance GPS ..............

[all star rod]

Good luck going with the Optimax..... I would get a HPDI 200HP in place of that MERC if you are looking with something besides the 4 stroke 150 Yamaha. Does Haynie have an agreement in place with MERC? I guess I am just a Yamaha guy. The only down side of going with the 101# troll motor is the extra battery. I think an 80# is more than enough. But nothing wrong with have too much power.

["W"]

I want a 4 stoke yammy....just getting a price with Mercury.....

[Salty]

What does this boat cost for example with a 150 4 stroke Yamaha...ready to fish. I am sure the troll motor is extra...80# thrust plus GPS/Fishfinder.


W doesn't need a "GPS/Fishfinder". He knows where to go to catch fish and his dinks won't show on the sonar.

[huntin fool]

W doesn't need a "GPS/Fishfinder". He knows where to go to catch fish and his dinks won't show on the sonar.
there installing a special gps/BIRD FINDER :*****::*****::*****:

[Capt. Ryan Rachunek]

sure it wasnt just the one you heard....my cousin runs one on back of his yellowfin in venice..and that thing is sweeeett...

just not on gas so much..

I was on a boat with twin 350's, don't know if it makes a difference.... Strong motors, I just didn't care for them....

[LaAngler]

the fly by wire verado 350 supposed to be better

[redspeck82]

Yea and the verado 350 is a V-6 insted of a V-8 so it might get alittle bet MPG.

[SULPHITE]

W I think there is a haynie boat hanging at spicers...

[cmdrost]

that is/was Stansels boat. I think he sold it already. gray 24HO

[SULPHITE]

yep thats it...

[cmdrost]

I want a 4 stoke yammy....just getting a price with Mercury.....


Get the 24HO with 250 4 stroke yammy!

[Reel Bender]

#1 I want a boat no body on our lake has....only seen one so far...#2 I heard that are smooth riding boats and take a good chop.....#3 I like the deck lay out!!! Short guy sides

With as much pooh as you fling, you might want to consider something that blends in with the rest!;)

["W"]

With as much pooh as you fling, you might want to consider something that blends in with the rest!;)


Back Back Give ME 50Feet

[MERCURY OUTBOARD MAN]

i dont know were you are at but in lake charles there is several 24 high outputs and one Z21 if you need names send me a pm and we can set up a demo i am building 2 more for the guys at hackberry rod and gun we do not offer the flats models anymore we do offer the new 21 cat and we are building the new 24 cat i do not have a cat in la yet so if anyone of yall from there want one i will make a special deal on 2 boats to get some over there i do deliver to la we sell 3-4 of the 21 cats a week they are fast dry and smooth and run were you should not run thanks for the interest in texas #1 built bay boats HAYNIE !Im looking at the 20foot or 21 foot does anyone around here have one? I would like some info before I drive to Texas!!

How much does the 24ft cost?

[MERCURY OUTBOARD MAN]

The plastic lids and cleats are an option we do use fiberglass lids and pull up ss cleats if you want these boats are custom we have right at 200 guides using these boats from baffin bay to lake charles the rougher the water the better they will run the 24 high output with 225 pro xs will run 60-64 mph thats not bad for a 24 ft boat without a doubt, a 200 or 225 will get you a lot better cruise speed not to mention top end. Plus it doesn't have to work as hard as a 150 which will improve mileage. A pad boat like that will not perform right without enough horsepower to lift the nose up.

In some of the pictures i saw some plastic lids and plastic cleats, not sure why they wouldn't just use glass lids and stainless.

One thing about the speckle paint finish inside is that it's much easier to keep looking clean

[MERCURY OUTBOARD MAN]

The z 21 with 225 proxs will run 4 mph over rpm if you are looking at getting a yamaha go on their web site and look at the test data they have done on boats. Maybe yours was not tested but i am sure you can find one that is pretty close to the weight and hull design of the one you are looking at(haynie). Hard to believe that boat has a weight of 1,350# and rated for a 250hp. The test results/data that yamaha did with the 4 stroke 150/xpress x22bay are pretty dang accurate compared to the way mine runs....fuel ecomony, top speed, speed @ rpms, and plane time. If anything the test data is conservative based on the load weight during the test. I usually have more weight in my boat since i fish three 90% of the time. Also, a 4 stoke can run at higher rpms than a 2 stroke di motor. I bet the optimax has the same range as the hpdi...5,500 rpms compared to a 4 stoke at 6,000 rpms. I bet that boat would fly with a 225 optimax!
I think the 150 yamaha 4 stoke is more than enough motor for that boat...get a jack plate.

[MERCURY OUTBOARD MAN]

Yes HAYNIE is the biggest mercury dealer in texas we are yamaha dealers also the z21 with 150 yamaha 4 strk starts out at $32000.00 pm me and i will tell you what you get at that price its not a stripped down mdl for sure and for the comment on grab rails around windsheild they all come with them we sell so many of these boats its hard to get finished products because everyone is in a hury we sell everyone built in all models Haynie has been the #1 boat in corpus christi area for 2 years check em out you will love them for sureGood luck going with the Optimax..... I would get a HPDI 200HP in place of that MERC if you are looking with something besides the 4 stroke 150 Yamaha. Does Haynie have an agreement in place with MERC? I guess I am just a Yamaha guy. The only down side of going with the 101# troll motor is the extra battery. I think an 80# is more than enough. But nothing wrong with have too much power.

[Hopedale Hustler]

the fly by wire verado 350 supposed to be better

the only problem with that is its a Mercury.....mite be just me..but had too many bad experiences with Mercs..

["W"]

That's what I want z21 with the 150 yammy 4 stroke!!!

[Reel Bender]

That is probably too Much boat for a little guy like you maybe you should consider one of these!!!! :D

[Salty]

That is probably too Much boat for a little guy like you maybe you should consider one of these!!!! :D



Bender, that one's bigger than the one he's got now. :eek:

[Reel Bender]

I know, I figured it would be a step up!!!

[cmdrost]

mercury man.....

How does the z21 perform with the yammy F150?

["W"]

mercury man.....

How does the z21 perform with the yammy F150?

I talked to him on PM and he said the Yammy 150 would push Z21 good....Im calling him this afternoon and get more details....I just dont see how a Merc can beat a 4 stroke Yam...

[Capt. Ryan Rachunek]

I talked to him on PM and he said the Yammy 150 would push Z21 good....Im calling him this afternoon and get more details....I just dont see how a Merc can beat a 4 stroke Yam...

You've obviously never been on a Merc powered Haynie.......

[Jay]

I talked to him on PM and he said the Yammy 150 would push Z21 good....Im calling him this afternoon and get more details....I just dont see how a Merc can beat a 4 stroke Yam...

I'm going out on a limb here. There is only one 2 stroke motor I will own and thats a Mercury optimax. If I was to buy a 4 stroke it would be a Suzuki. It uses a timing chain not some high maintenance belt motor.

[Salty]

You've obviously never been on a Merc powered Haynie.......



The guide I fished with in S. Texas had a Mercury-powered Haynie. That sucker would fly.:eek:

["W"]

The guide I fished with in S. Texas had a Mercury-powered Haynie. That sucker would fly.:eek:

Im not trying to fly...just fish:rotfl::rotfl:

[all star rod]

Merc....will fly into the boat shop for a monthly repair!!:rotfl::*****::*****:Fished Big Lak yesterday and we picked up 24 trout and 3 white trout all on plastics and top water. Also, I saw what looked like to be a 24' Haynie (likely a guide boat).

[Ray]

I saw a very nice looking Shearwater in Big Lake yesterday with a big Mercury on the back. It had MI letters. Is that Michigan, Mississippi or Missouri?

[all star rod]

Ray I saw it too as I was leaving the landing. It was parked on the side road by a camp....pretty color....looked to be a very dark blue. Those are nice boats. I would assume a 24' would run you $50K easily.

["W"]

Ray I saw it too as I was leaving the landing. It was parked on the side road by a camp....pretty color....looked to be a very dark blue. Those are nice boats. I would assume a 24' would run you $50K easily.

About $70 rigged out

["W"]

This is what im going to power it with....

[LaAngler]

Merc....will fly into the boat shop for a monthly repair!!

i've ran mercs for years with no problems

a 2 1/4 opti will make that F150 feel like a dog

http://www.youtube.com/watch?v=uwJB4D0Sl7k

[Deadly D]

[QUOTE=all star rod;26045]Merc....will fly into the boat shop for a monthly repair!!:rotfl::*****::*****:QUOTE]


i've ran mercs for years with no problems

a 2 1/4 opti will make that F150 feel like a dog

http://www.youtube.com/watch?v=uwJB4D0Sl7k
he will be crying after he gets caught un a thunder bommer and doest make it in in time or when he puts 3 or 4 people and gear in it. Oh well thats him:*****:

[all star rod]

He will be crying when that storm is coming and that MERC will not start. I think when you buy a MERC it automatically comes with one year free of SEATOW and a marine radio...:*****::*****:Also, going an extra 5-7 mph faster will save you what 2-3 minutes over a 10 miles stretch.

["W"]

He will be crying when that storm is coming and that MERC will not start. I think when you buy a MERC it automatically comes with one year free of SEATOW and a marine radio...:*****::*****:Also, going an extra 5-7 mph faster will save you what 2-3 minutes over a 10 miles stretch.


NOW THAT FUNNY RIGHT THERE:*****::*****::*****::*****:..... 25hp Merc I will take all day....but when it comes to big motor.....Yammahammer :D

[LaAngler]

i had a fairly late model 25 merc i thought it sucked

225 HPDI would be nice too

[all star rod]

Really if I ever owned a MERC it would be an Optimax. I just think Yamaha is a better motor. Most guides and people that run crab traps have Yamaha 4 strokes. This should tell you something since they are on the water basically every day. The 4 stroke Yamaha 150 is a lot more powerful/work horse motor than you would think and it is very, very quiet!

[Deadly D]

i had a fairly late model 25 merc i thought it sucked

225 HPDI would be nice too
U right ever since they got awawy from the chrome cylinder wall they went to briggs and stration throwaways

[huntin fool]

U right ever since they got awawy from the chrome cylinder wall they went to briggs and stration throwaways



game wardens run a merc something...dont know wether it was hpdi or optimax..QUIET! i couldn't hear it at all while they chewed us out..didn't even know it was running til he threw it in reverse while a wave came...

had yellow stripes..quiet...fast...

[Salty]

I saw a very nice looking Shearwater in Big Lake yesterday with a big Mercury on the back. It had MI letters. Is that Michigan, Mississippi or Missouri?


Meeshigun

[Montauk17]

I ride in boats daily and trust me,you dont want a 150 fourstroke on a 22 foot boat.Get yourself a 225 opti or hpdi and you will be much more happy.

[all star rod]

W did you ever find out what that 21' Haynie runs with a 150 4 stroke & 225 Opti ready to fish....just wondering what the price range is.

[Ray]

I have a 19' Cobia bay boat with a 150 Yahama 4 stroke. It runs 50 mph wide open with me and the wife, full of gas, eats and drinks, and about 43 mph loaded with me and Jfranovich(BIG ole country boy), 3 full ice chests, and supplies for an all day fishing trip.
I run about 35 mph at 4500 rpms fully loaded. She gets on top step o.k., but not like my old boat with a 2 cycle Mercury.
But my fuel economy is pretty great compared to my old 2 cycle Mercury.
I can talk to anyone fishing with me when running at any speed. The Yamaha is a super quiet motor.
My boat doesn't have rolled sides, she has the liner. She weighs 1960 lbs. dry, without engine.
I got her because it was one of the few boats that would fit in my car port and it had a 60 gal. gas tank.
I don't know now well a 150 would push a 22 ft'er, unless it is a light boat.

["W"]

W did you ever find out what that 21' Haynie runs with a 150 4 stroke & 225 Opti ready to fish....just wondering what the price range is.

29,000 to 35,000

[Ray]

Plus taxes and registration?
I live in Lake Charles(9% tax) and it killed me when they added the taxes and registration. When I lived in Cameron, we only had a 4% tax.
My Cobia was $27K and it ended up being $30K after titling the trailer, registering the boat and fokking me with the 9% tax.

["W"]

Plus taxes and registration?
I live in Lake Charles(9% tax) and it killed me when they added the taxes and registration. When I lived in Cameron, we only had a 4% tax.
My Cobia was $27K and it ended up being $30K after titling the trailer, registering the boat and fokking me with the 9% tax.


Thats just some base prices.....I havent got all the details yet but I may just get the Z21 with the 225 Opt,Jack Plate,Power pole,trolling motor and GPS....Im sure it will run high 30s lower 40s....

[Deadly D]

Thats just some base prices.....I havent got all the details yet but I may just get the Z21 with the 225 Opt,Jack Plate,Power pole,trolling motor and GPS....Im sure it will run high 30s lower 40s....
Thats what Im talking about. I might start fishing with you more:*****:

[all star rod]

W was the 225 Opti more $ than the best outboard ever made: "4 stroke 150 Yamaha"?

["W"]

W was the 225 Opti more $ than the best outboard ever made: "4 stroke 150 Yamaha"?

I dont know that for sure.....We havnt talked about the Opti yet...... Im just going off prices other guys have paid with kind of what I want....he is calling me back after the 1st with all info.... This boat will run mid to high 30's with tax and equi....I getting mine loaded becasue I hope it last 10-15years....

[all star rod]

Rule #1 when you buy a boat get everything you need at the time of purchase from the dealer.....For example, I bought a radio & he threw in the jack-plate....that kind of thing!

[LaAngler]

wonder what kind of buy 2 boats discount they would give

i think the same dealer has kenner also, be interesting to know how the performance of the haynie vs kenner is

["W"]

wonder what kind of buy 2 boats discount they would give

i think the same dealer has kenner also, be interesting to know how the performance of the haynie vs kenner is


Once I get to talk to him ...I will make my mind up on the Merc or yammy......Just need someone to talk me into going Merc...

[Deadly D]

Once I get to talk to him ...I will make my mind up on the Merc or yammy......Just need someone to talk me into going Merc...You wont be disatisfied with the optima Im telling you. Ill even work on it for you but you wont have to worry about that if you take care of it.

[Natural Light Kid]

Plus taxes and registration?
I live in Lake Charles(9% tax) and it killed me when they added the taxes and registration. When I lived in Cameron, we only had a 4% tax.
My Cobia was $27K and it ended up being $30K after titling the trailer, registering the boat and fokking me with the 9% tax.

that's one of the nice things about getting a used rig! :)

[boatdriver]

I run an Optimax and the rest of our lodge runs them. I was gonna buy a Blackjack but will probably go with a Haynie 24 and just sell it every year to buy a new one. Gonna put a 225 Pro XS on the back of it. We have 2 Haynie's right now and we'll probably be running at least 4 next year. Sweet riding boats. Chris is a good guy to deal with. He helps you out any way that he can.

BD

[Deadly D]

I run an Optimax and the rest of our lodge runs them. I was gonna buy a Blackjack but will probably go with a Haynie 24 and just sell it every year to buy a new one. Gonna put a 225 Pro XS on the back of it. We have 2 Haynie's right now and we'll probably be running at least 4 next year. Sweet riding boats. Chris is a good guy to deal with. He helps you out any way that he can.

BD
How does a Haynie compare to the Blackjack 22' model

[Raymond]

Meeshigun
I thought the same thing but, it is actually Mississippi.

[Capt. Ryan Rachunek]

I thought the same thing but, it is actually Mississippi.

MS is the abbreviation for Mississippi.....

Here is Merc's info.....
Mercury Racing
N7480 County Road UU
Fond du Lac, WI 54935
Phone: 920-921-5330
FAX: 920-921-6533




Mercury Marine
W6250 W. Pioneer Road
P.O.Box 1939
Fond du Lac, WI 54936-1939

They are out of Wisconsin.....

[Raymond]

MS is the abbreviation for Mississippi.....
Not on Boats, brother lives in Greenville Ms and all of the boats at the yatch club have MI on them. Don't worry it won't be the first time you have been wrong.

Here is Merc's info.....
Mercury Racing
N7480 County Road UU
Fond du Lac, WI 54935
Phone: 920-921-5330
FAX: 920-921-6533




Mercury Marine
W6250 W. Pioneer Road
P.O.Box 1939
Fond du Lac, WI 54936-1939

They are out of Wisconsin.....

Not on Boats, brother lives in Greenville Ms and all of the boats at the yatch club have MI on them. Don't worry it won't be the first time you have been wrong.

[MERCURY OUTBOARD MAN]

I dropped kenner 2 years ago tracker marine just dont build them like bill kenner did to many warranty issues and a pain in the a-- to deal with we only sell Haynie and will make you a deal on 2 for sure wonder what kind of buy 2 boats discount they would give

i think the same dealer has kenner also, be interesting to know how the performance of the haynie vs kenner is

[cmdrost]

"tracker marine just dont build them like bill kenner did"

You got that right......I'm ready for k2 marine to come out with the 24 ft frontier.

[boatdriver]

How does a Haynie compare to the Blackjack 22' model


Well, for one the Blackjack is a boat with a cap. The Haynie's have wood whereas the Blackjack's do not. Now, Chris says that the wood is all glassed over, so, we'll see. The price is also a factor; about $8,000 difference. I personally like the Blackjack, but wish it was a 24'. If Bill Kenner makes a 24' Blackjack, you will see them all over the lake, as they will be a lifetime hull. I would be going from 24' to 22.5' fishing 3 people plus me everyday. Not sure how it will be. THe Haynie is 24' and just a little narrower than the BJ. Ultimately, 2 great boats with different pros and cons. It's all about preference.

BD

[Ray]

In my opinion, I would not get a boat with wood in it, even if it was glassed over, if I were keeping it for a long time. Sooner or later, water will rot the wood if you use it enough. I have seen a lot of boats at Olmsted Shipyard fixing soft decks and transoms from wood rot. Water seems to seep down screws used for seats and tops. There are ways to prevent this, if the boat builder builds it right. But I still would rather not take the chance. There are too many new coring products that can take the place of wood, but will not rot like wood.

[cmdrost]

Bill Kenner told me at the last boat show that a 24 blackjack and 24 frontier are in the works and should be out by 2010.

[boatdriver]

Drost, we've been hearing about a 24 BJ and Frontier since he startted building them. Those will be some great boats. If I am not mistaken, and maybe I am, the Frontier has wood and the BJ does not. Most all non-capped boats will contain wood. Haynie's are SOLID built boats and so are Bill's boats. Either way, W or myself will have a good boat for years to come.

[MERCURY OUTBOARD MAN]

The wood we use is called boat panel you can not buy at lowes are home depot it comes with a 100 year warranty against rot,the composite on the other hand does have a lifetime warranty against rot and rot only but what happens when your motor falls of the back of your boat like more than 1 has done in the IFA tournament out of kema and texas redfish series. both were composite boats and i talked to one of the owners of one of the well known boat builders and he was told if he could use the boat panel like he did on most all of the boats he has built threw the years this would not have happened in my eyes the composite deal is a sales pitch.look at 2 year old composite boat that has been run in rough water you will see stress cracks every where and thats considered not warranty,some ofthe best selling boats come from texas and they all have wood and its for a reason <strength> In my opinion, I would not get a boat with wood in it, even if it was glassed over, if I were keeping it for a long time. Sooner or later, water will rot the wood if you use it enough. I have seen a lot of boats at Olmsted Shipyard fixing soft decks and transoms from wood rot. Water seems to seep down screws used for seats and tops. There are ways to prevent this, if the boat builder builds it right. But I still would rather not take the chance. There are too many new coring products that can take the place of wood, but will not rot like wood.

[Ray]

I keep a Chris Craft boat at Olmsted Shipyard in a boat shed there. I have seen a LOT of boats come in to get soft decks fixed due to rotten wood. I have to believe what I see, not what I hear.

[LaAngler]

The wood we use is called boat panel you can not buy at lowes are home depot it comes with a 100 year warranty against rot,the composite on the other hand does have a lifetime warranty against rot and rot only but what happens when your motor falls of the back of your boat like more than 1 has done in the IFA tournament out of kema and texas redfish series. both were composite boats and i talked to one of the owners of one of the well known boat builders and he was told if he could use the boat panel like he did on most all of the boats he has built threw the years this would not have happened in my eyes the composite deal is a sales pitch.look at 2 year old composite boat that has been run in rough water you will see stress cracks every where and thats considered not warranty,some ofthe best selling boats come from texas and they all have wood and its for a reason <strength>


good information here

["W"]

Talked to Chris today....These boats are the real deal....They come loaded .... I think I'm sold on the Z21 w/225 Opti Max...Body Black....Hope this all goes like I have Planned.

[BigCoon]

Talked to Chris today....These boats are the real deal....They come loaded .... I think I'm sold on the Z21 w/225 Opti Max...Body Black....Hope this all goes like I have Planned.

Are you still getting the boat after Cora found out about you buying the site?

[LaAngler]

Talked to Chris today....These boats are the real deal....They come loaded .... I think I'm sold on the Z21 w/225 Opti Max...Body Black....Hope this all goes like I have Planned.

quiksilver baby, merc all the way

jet black helps you sneak up on the fish better, but if you want it to look good at 10 years old get solid white.

[Ray]

Those are some pretty light boats for a 21 ft'er. I bet it hauls @$$...

["W"]

Those are some pretty light boats for a 21 ft'er. I bet it hauls @$$...


65mph!!!!:p

[Austin(boatman's son)]

what size motor?

[Austin(boatman's son)]

dubya is really gonna hop the waves now haha

[SULPHITE]

HERE

I think I'm sold on the Z21 w/225 Opti Max...

[Austin(boatman's son)]

HERE

Yup, it will cruise. Dubya gunna look like a kid in that big boat!!!! :*****::*****: jk dubya lol

[Montauk17]

Wood in a boat is not a bad thing at all if it's done right. My boston whaler is a 1970 model,and it has wood in it....still solid as a rock.I've never really heard of a haynie untill now,but it seems to be a well built boat from what I can see.

[all star rod]

The boat will not be an issue.....I would be more worried about the Merc motor:puke:

[Austin(boatman's son)]

The boat will not be an issue.....I would be more worried about the Merc motor:puke:

Nothing wrong with a merc!!! :shaking:

[Ray]

Nothing wrong with a merc!!! :shaking:

I agree. I had fantastic luck with the two I had.

[Hopedale Hustler]

its amazing how long this thread has lasted and prety much stayed on the topic of boats and motors....ima bout to jack it...Bombers dont catch big trout...haha

[huntin fool]

Nothing wrong with a merc!!! :shaking:




how ya know that nothing is wrong with mercs? how many mercs have you run? :smokin:

[Ray]

That 21 ft. Haynie weighs 1400 lbs. dry.
My 19 ft. Cobia weighs 1960 lbs. dry.
That is a lot of difference. It don't draw much water either.
With a 225 HP on the back, your tears are gonna freeze in the winter...

[Austin(boatman's son)]

how ya know that nothing is wrong with mercs? how many mercs have you run? :smokin:

doesnt matter how many i ran, i do research :shaking:

[evis102]

Z21 with a Merc 250XS(not the pro), Bucket seats, Short console(to fit under wier), 10" Jackplate, 8' Power Pole(with remote), #101 Minn Kota, Onboard chargers, Lowrance HDS-8. Perfect Boat

[evis102]

http://i86.photobucket.com/albums/k110/Shroomtip/Picture20455.jpg
http://i86.photobucket.com/albums/k110/Shroomtip/Picture20454.jpg


Something like this but 21' with a 250XS

[huntin fool]

http://i86.photobucket.com/albums/k110/Shroomtip/Picture20455.jpg
http://i86.photobucket.com/albums/k110/Shroomtip/Picture20454.jpg


Something like this but 21' with a 250XS



WOW. all i can say

[LaAngler]

now that is a fine boat