SaltyCajun.com http://louisianaofficesystems.com/
MESSAGE BOARD Register Weather/Tides/Launches Store Go Premium! Sponsors Raffles Mark Forums Read

Notices

Go Back   SaltyCajun.com > Fishing Talk > Boating Talk
Reload this Page Jack plate needed

Boating Talk For discussion of everything related to boats and motors

Reply
 
Thread Tools Display Modes
  #1  
Old 07-30-2011, 05:06 PM
Natural Light Kid's Avatar
Natural Light Kid Natural Light Kid is offline
Red Snapper
  
Join Date: May 2009
Location: Lake Charles
Posts: 1,100
Cash: 1,090
Default Jack plate needed
Just bought a 16/50 flatbottom with a 40 HP Tohatsu. I am looking for a jack plate if anyone out there has one. Thanks.
Reply With Quote
  #2  
Old 07-30-2011, 05:21 PM
Hydro's Avatar
Hydro Hydro is offline
King Mackeral
  
Join Date: Jan 2011
Location: Lake Charles
Posts: 2,123
Cash: 5,104
Default
Are you looking to buy one, or looking for info ???

Hydro
Reply With Quote
  #3  
Old 07-30-2011, 06:48 PM
Natural Light Kid's Avatar
Natural Light Kid Natural Light Kid is offline
Red Snapper
  
Join Date: May 2009
Location: Lake Charles
Posts: 1,100
Cash: 1,090
Default
I'm sorry. Buy one.
Reply With Quote
  #4  
Old 07-30-2011, 07:18 PM
scott craft scott craft is offline
Tripletail
  
Join Date: Jan 2011
Location: Moss Bluff
Posts: 665
Cash: 1,215
Default
The place on Gulf Highway makes the best for the money imo. Southside Welding is the name I think.

Sent from my Droid using Tapatalk
Reply With Quote
  #5  
Old 07-30-2011, 07:33 PM
Hydro's Avatar
Hydro Hydro is offline
King Mackeral
  
Join Date: Jan 2011
Location: Lake Charles
Posts: 2,123
Cash: 5,104
Default
Quote:
Originally Posted by Hydro View Post
Are you looking to buy one, or looking for info ???

Hydro
My 6" Hi-Jacker came from the Yamaha Shop, I would imagine that Lake Area or Jorgensens in Beaumont has them in stock...

Hydro
Reply With Quote
  #6  
Old 07-30-2011, 09:40 PM
Natural Light Kid's Avatar
Natural Light Kid Natural Light Kid is offline
Red Snapper
  
Join Date: May 2009
Location: Lake Charles
Posts: 1,100
Cash: 1,090
Default
Quote:
Originally Posted by Hydro View Post
Are you looking to buy one, or looking for info ???

Hydro
On that note, any suggestions on how much set back? I know I'm opening a can of worms now.
Reply With Quote
  #7  
Old 07-30-2011, 09:42 PM
Montauk17's Avatar
Montauk17 Montauk17 is offline
Great White
  
Join Date: Jul 2009
Location: Lafayette,LA
Posts: 10,803
Cash: 2,738
Default
http://www.cajunjacker.net/ I got one on my whaler,very good plate. On that size boat/motor a 4-5inch setback is all you need.
Reply With Quote
  #8  
Old 07-30-2011, 10:09 PM
Natural Light Kid's Avatar
Natural Light Kid Natural Light Kid is offline
Red Snapper
  
Join Date: May 2009
Location: Lake Charles
Posts: 1,100
Cash: 1,090
Wink
Quote:
Originally Posted by Montauk17 View Post
http://www.cajunjacker.net/ I got one on my whaler,very good plate. On that size boat/motor a 4-5inch setback is all you need.
That's what I was thinking too. Dont think 6" is necessary in this case.
Reply With Quote
  #9  
Old 07-30-2011, 11:47 PM
Natural Light Kid's Avatar
Natural Light Kid Natural Light Kid is offline
Red Snapper
  
Join Date: May 2009
Location: Lake Charles
Posts: 1,100
Cash: 1,090
Default
What about 5 1/2" of setback? Looking at manual CMC one at bass pros shops and it has 5 1/2" of set back. I have beaucoup rewards points saved up with them.
Reply With Quote
  #10  
Old 07-31-2011, 12:14 AM
Montauk17's Avatar
Montauk17 Montauk17 is offline
Great White
  
Join Date: Jul 2009
Location: Lafayette,LA
Posts: 10,803
Cash: 2,738
Default
Setback is not very important on a jon boat...Unless you have a tunnel. If so you want the least amount of setback possible,tunnel runs best with the prop closer to the tunnel. Keep in mind the more the setback the more you have to reach for the tiller handle.
Reply With Quote
  #11  
Old 07-31-2011, 06:22 PM
Hydro's Avatar
Hydro Hydro is offline
King Mackeral
  
Join Date: Jan 2011
Location: Lake Charles
Posts: 2,123
Cash: 5,104
Default
6" setback worked for me, engine mount bolts are installed at the highest setting and jack plate is adjusted up as far as it will go... The engine sits a good 6-7" higher than the transom...

My Yamaha does have the big tiller on it however...

Hydro
Reply With Quote
  #12  
Old 12-12-2011, 07:54 AM
boben1968's Avatar
boben1968 boben1968 is offline
Flounder
  
Join Date: Dec 2011
Location: Louisiana
Posts: 44
Cash: 704
Default
I have a 1546VJ Express with a 25-3 cylinder yammy ( stock ). Running a 10 1/8 x 11P Powertech wheel set back 9", with cavitation plate 1" above bottom of boat. With boat loaded I am running 36-37 MPH...
Reply With Quote
  #13  
Old 12-12-2011, 10:29 AM
outcast's Avatar
outcast outcast is offline
Red Snapper
  
Join Date: Dec 2009
Location: Gonzales, LA
Posts: 1,203
Cash: 1,443
Default
http://tsgcustom.com/JsckPlate.aspx

Made for smaller motors. Electric or manual.
Reply With Quote
Reply

Bookmarks

« Previous Thread | Next Thread »
Thread Tools
Display Modes
Linear Mode Linear Mode

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump


All times are GMT -5. The time now is 11:03 PM.


Contact Us - Louisiana's Best Fishing, Hunting, and Outdoors Forum - New Posts - Mobile - Archive - Privacy - Terms - Top

Powered by vBulletin®
Copyright ©2000 - [ARG:3 UNDEFINED], Jelsoft Enterprises Ltd.
vB.Sponsors
vBCredits v1.4 Copyright ©2007 - 2008, PixelFX Studios
SaltyCajun.com logo provided by Bryce Risher

All content, images, designs, and logos are Copyright © 2009-2012,
Salty Cajun, LLC
No unathorized use is permitted
Geo Visitors Map