![]() |
![]() |
![]() |
|
Inshore Saltwater Fishing Discussion Discuss inshore fishing, tackle, and tactics here! |
![]() |
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
![]() |
#2
|
||||
|
||||
![]()
Check with Eric Simmons at SCB. Or Josh Finch at Full Throttle Boatworks. They will do 'try and buy' on props.
|
#3
|
||||
|
||||
![]()
Whats the new boat?? any pics
|
#4
|
|||
|
|||
![]()
Majek Illusion with 225 SHO
|
#5
|
||||
|
||||
![]()
I have a 22 Bravo my will not be back around the lake until next Wed
__________________
Waltrip's Saltwater Guide Service jeremy@geaux-outdoors.com https://m.facebook.com/waltrip.guideservice?id=148838538646862&_rdr |
#6
|
||||
|
||||
![]()
I have my 22 bravo I off of my motor and my ot4 on right now....I would let you borrow it but im at work till this weekend...you dont like the 23 ot4 you selling?
Sent from an Apple Tree.. |
#7
|
|||
|
|||
![]()
The OT4 is just alittle to much and the small hub lets it break loose to much.
|
#8
|
||||
|
||||
![]()
Post a picture of that bad boy on the salty cajun boat show thread
sent from my Galaxy NOTE II |
#9
|
||||
|
||||
![]()
X2, also a compare/contrast vs your 23ls would be cool
|
#10
|
||||
|
||||
![]()
my ot4 slips a lil bit also but hooks right back up...ive just gotten used to it...ive got the bravo I XS that I got from you still. I had it dropped to a 25 though.
Sent from an Apple Tree.. |
#11
|
||||
|
||||
![]() Quote:
The 4.2L Yams (SHO included) do not need the extra ventilation. Never heard of an OT4 breaking loose, unless no blowout ring on a SHO. I ran a 25 OT4 on a 250 SHO that ran right with the 26 B1XS - 74 mph. It bites like a pit bull and will not turn loose from my experience. Call Mark Croxton and get his large hub Razor 4 - large hub with big stout blades. He will fix you up. > http://www.marksprops.com/products.html Good luck. |
#12
|
||||
|
||||
![]()
What you guys mean when you say the prop is slipping?
sent from my Galaxy NOTE II |
#13
|
||||
|
||||
![]()
the prop will lose its bite due to the way they are setup....the bravo I XS has holes in front the blade to allow exhaust to help with holeshot...with the ot4 prop being a small hub, at a certain point during acceleration(different setups different point at which it will slip) it will lose its bite(slip-motor will rev a little more than normal) but once the speed and amount of water feeding the prop equalize a bit it will hook up hard again....with the ot4 style prop its usually on take off....bout the best way I can explain it.
Sent from an Apple Tree.. |
#14
|
||||
|
||||
![]()
O ok. Same as if your going around a curve fast and motor reves up Right
sent from my Galaxy NOTE II |
#15
|
||||
|
||||
![]()
yea...with it trimmed up and turning some props will cavitate mire than others
Sent from an Apple Tree.. |
#16
|
|||
|
|||
![]()
I had 2 rings on the OT4. The Majek Illusion is a shallow water boat. Pretty much a flat bottom with a huge tunnel. Is a whole different animal than the 23LS.
|
#17
|
||||
|
||||
![]()
To be clear, the blow out preventer ring wraps the entire prop hub forward of the blades. You physically cannot have 2 on at the same time - so I guess you mean 2 PVS hole plugs. No venting at all needed on the SHO.
|
#18
|
||||
|
||||
![]()
Ive read on other sites, that on the majek's, guys are having to run the blow out rings with the ot4's...
Sent from an Apple Tree.. |
#19
|
|||
|
|||
![]()
To be clear I had 2 rings on it so as to fill the entire gap. Ill post a pic later. Never doubt my ingenuity. 2 rings did more than one but it was still to much to stay hooked up in the tunnel.
|
#20
|
||||
|
||||
![]()
Yea, I was thinking Majek extreme
|
![]() |
Bookmarks |
|
|