|
|
|
|
|||||||
| General Discussion (Everything Else) Discuss anything that doesn't belong in any other forums here. |
 |
|
|
Thread Tools | Display Modes |
|
#1
03-23-2010, 09:46 AM
|
||||
|
||||
garmin problems
|
|
#2
03-23-2010, 10:16 AM
|
||||
|
||||
i have the same problem with mine. While running the depth says the last depth it was whenever i was not moving. Does'nt pick up depth on the move.
|
|
#3
03-23-2010, 11:31 AM
|
||||
|
||||
|
Mine does the same thing.
|
|
#4
03-23-2010, 11:34 AM
|
||||
|
||||
|
Mine did that...adjust your transponder on the boat it probably got bumped when you were putting it on the trailer. I just pushed it down one notch then tightened it up real good. Works fine now
|
|
#5
03-23-2010, 12:03 PM
|
||||
|
||||
|
meaux do u have a Garmin
|
|
#6
03-23-2010, 12:05 PM
|
||||
|
||||
|
Quote:
|
|
#7
03-23-2010, 12:08 PM
|
||||
|
||||
|
maybe I need to adjust the angle because when we went the other day it had never been tailored since I put it on
|
|
#8
03-23-2010, 08:00 PM
|
||||
|
||||
|
its hard to get a good reading with a transom mounted transducer while on step. when you get on step you get more air bubbles coming through and it will throw off the reading. best thing to do if your boat is glass is to bond the transducer inside the hull.
|
|
#9
03-31-2010, 06:51 PM
|
||||
|
||||
|
i got another problem too i think my transducer is causing my boat to lean when im on plane. that is the only thing i can figure. i didn't start till then......anyone else ever had this problem
|
|
#10
03-31-2010, 06:53 PM
|
||||
|
||||
|
Quote:
???? i wouldn't think that little transducer would cause that...
|
|
#11
03-31-2010, 06:56 PM
|
||||
|
||||
|
garmin transducer ain't too little
|
|
#12
03-31-2010, 07:07 PM
|
||||
|
||||
|
i know, i have one. BUt seriously, i don't think that would mess it up.
|
|
#13
03-31-2010, 07:14 PM
|
||||
|
||||
|
if it ain't that then i don't know why it would all of a sudden start that unless my jackplate got out of wack
|
|
#14
03-31-2010, 07:38 PM
|
||||
|
||||
|
You may be taking on water where you drilled the holes.........I agree with transducer needing to be moved to read underway.......Adam, your aluminum? The comment about the bubbles is also correct, but specktator, your whaler shouldn't make lots of bubbles.
Is the transducer to close to the motor? That'll screw it up too......good luck
|
|
#15
03-31-2010, 07:40 PM
|
||||
|
||||
|
no water I have a glass boat too
|
|
#16
03-31-2010, 09:55 PM
|
||||
|
||||
|
you ever get your prop checked?
|
|
#17
03-31-2010, 09:57 PM
|
||||
|
||||
|
no I forgot about it after being gone to chicago.......that may have something to do with it
|
|
| Bookmarks |
|
|
Linear Mode
