|
General Discussion (Everything Else) Discuss anything that doesn't belong in any other forums here. |
|
Thread Tools | Display Modes |
#41
|
||||
|
||||
|
#42
|
||||
|
||||
Quote:
Alright, so you're an expert on classes and can't afford a backup propane tank to plug in if you run out during a crawfish boil. Nor do you know about the economics of a long term investment to reduce your cost of ownership by refilling your own tanks at the local hardware store. Maybe the vibration in your truck is so unbearable that you can't stomach the extra miles to the hardware store? The blue rhino is just so much closer? |
#43
|
||||
|
||||
Quote:
|
#44
|
||||
|
||||
UPDATE:
I tapped into the gas line in the attic and ran a water hose from the 1/2" ball shut off valve to the 23 jet burner outside (because it was a quick easy way to have a long hose with quick connect fittings on it) and im happy to say it works nicely so far just laying on the top of my old propane burner. the only thing I can use to compare at this time is the intensity of noise it makes and with the natural gas 23 jet it is about 2/3 as loud as the single jet propane burner noise when on full. even if it is slower to boil with, as I suspect it will be, it does show it will be a fantastic outdoor cooker for just about anything. the only question is will it make a good boiler for large pots. until I get a burner stand built for it, I cant measure time to boil an 80 quart pot but for now it seams to be throwing a nice flame even though its hard to see the flame in daytime. now I know that it works I can go through the work and expense to run a gas line through the attic to where I want it to be and then after that's all set up I can look into getting a boiler frame and stand that is suitable to be modified to fit the 23 jet burner or if need be maybe have one made from scratch is my next task. |
#45
|
||||
|
||||
just ordered this cooker: http://www.ebay.com/itm/301562479231?_trksid=p2057872.m2749.l2649&ssPageNa me=STRK%3AMEBIDX%3AIT
it looks very suitable with a large enough diameter ring to fit the 23 jet natural gas jet burner in with a little side clearance and its definitely much more solidly built then most of the ones I've seen, plus its all powder coated finish and not just painted like the others. |
#46
|
|||
|
|||
Quote:
|
#47
|
||||
|
||||
Quote:
|
#48
|
||||
|
||||
Quote:
I ran gas lines for houses as well as plumbing and electrical even though my main profession was a/c repair and installation. the company I worked for did it all so every now and then we also got the contract for gas and electrical work. |
#49
|
|||
|
|||
Awesome Thread
Lol, wow this thread is winning. I guess we all have an expiration date but some people work very hard to expedite that date.
|
#50
|
||||
|
||||
LMAO
|
#51
|
||||
|
||||
http://g4burner.com/
this is the one I got in Raceland, LA... love it and doesn't clog up like the one with the jets.. JMO |
#52
|
||||
|
||||
Quote:
|
#53
|
||||
|
||||
UPDATE:
ok its done and it works great with just regular residential gas pressure and nothing special being done to the gas line or gas meter. here are the videos showing the finished product part 1 shows the burner https://www.youtube.com/watch?v=I5otcRH81bE part 2 shows the burner in action https://www.youtube.com/watch?v=Shx2UsJc7T0 a few notes - - an 80 quart pot half full of water takes 25 minutes to reach a regular boil and 5 more minutes (30 minutes total) to reach a rolling boil from cold and I simulated a basket of crabs by dumping in a little over 2 gallons of cold water in and it took 10-12 minutes to return back to a regular boil and 3 minutes longer then that to get back to a rolling boil. - the time it takes water to boil (as expected) is about double that of my propane burner but its not that big a deal. so what if it takes 15 minutes longer to start boiling when you never have to fool with propane tanks ever again. - the legs were connected using a standard 1 1/2" long 3/8" bolt with big oversized washer - the wind guard ring gets very hot (as expected) but the bottom part below the burner ring stays much cooler with only the heat migration causing it to get hot but its not hot enough to burn the powder coat. - even though it works great just like it is, I plan to ask the gas company to come by and test the gas supply pressure to the house. I figure it wouldn't hurt to be sure to confirm that it is set at the upper range of allowed residential gas pressure to the house. - those spark ignition things you buy to light burners with wont work, I had one laying around so I tried it and the gas flame is just too low a pressure to light reliably until you have a gas pocket built up and get a big "poof" of flame come out at you, so stick to a regular stick style lighter for lighting the burner. Last edited by keakar; 04-08-2015 at 02:59 PM. |
#54
|
||||
|
||||
I wanted to add that the times I gave in the post above were all done for an uncovered pot during the timings.
naturally a covered pot would heat up (and reheat) faster but I didn't feel it would be worth calling a success if you had to cover a pot to make it work. |
Bookmarks |
|
|