Minn Kota Rip Tide 70

[plumber69]

I'm pulling my hair out with a new rip tide. Motor is wired correctly and the 50 amp fuse is in place. The first trip out, I got 4 hours use out of it before it died. I took it to Minn Kota authorized service center and was told the brush holder was bad. Took it out this weekend and got maybe 20 minutes before the same thing happened. I was asked if I was running it hard. I do not understand this question because I was going against the tide for the 20 minutes but cannot believe that this would cause a brand new motor to burn up. I talked to a few other people and their salesman asked them the same question about running it hard. Is that the same as telling me I shouldn't run my outboard motor wide open? Has anyone else had a problem with these motors? I did return it to Academy with no questions asked and got a new one. Hoping this was just a lemon.

[calcutta37]

Lemon!!!

[keakar]

Originally Posted by plumber69

I'm pulling my hair out with a new rip tide. Motor is wired correctly and the 50 amp fuse is in place. The first trip out, I got 4 hours use out of it before it died. I took it to Minn Kota authorized service center and was told the brush holder was bad. Took it out this weekend and got maybe 20 minutes before the same thing happened. I was asked if I was running it hard. I do not understand this question because I was going against the tide for the 20 minutes but cannot believe that this would cause a brand new motor to burn up. I talked to a few other people and their salesman asked them the same question about running it hard. Is that the same as telling me I shouldn't run my outboard motor wide open? Has anyone else had a problem with these motors? I did return it to Academy with no questions asked and got a new one. Hoping this was just a lemon.

probably a bad batch of motors, the fact they are asking the same question to others is a sign they are having a lot of problems with it.

if I were you i would try to repeat the same conditions again a few more times to be sure this motor works correctly but if you have the same issue again with the new motor switch to a different size or type that doesn't use the same components as that one or if that isn't an option then just try a motorguide instead

[plumber69]

Originally Posted by keakar

probably a bad batch of motors, the fact they are asking the same question to others is a sign they are having a lot of problems with it.

if I were you i would try to repeat the same conditions again a few more times to be sure this motor works correctly but if you have the same issue again with the new motor switch to a different size or type that doesn't use the same components as that one or if that isn't an option then just try a motorguide instead

I will be back on the water flounder gigging Saturday if conditions are good. I will try to repeat the conditions. I believe you are correct that they may have had a bad batch but hopefully I can get this resolved. Hard to fish without the trolling motor.

[Brinnon]

I've had the same trouble with mine since I purchased it. Always kept a spare set of brushes and brush holders in the boat for a quick change out. Used to get them from online @ Mikes Reel repair. They seem to hold up better than OEM

[huntergather86]

I have the same trolling motor brand new took it to lacassine ran it full blast through thick grass and had no problems

[Visco]

I run the sh#@ out of mine for hours every weekend. I have two batteries and run them pretty much until they die, which is normally my sign that it is time to go in. "Knock on wood" no issues yet and have run into grass, and oysters. I need another prop due to the oyster beds. I think maybe you're under powered. I have the 120 on a 20' tidewater.

Sent from my SAMSUNG-SGH-I547 using Tapatalk

[Visco]

Originally Posted by Visco

I run the sh#@ out of mine for hours every weekend. I have two batteries and run them pretty much until they die, which is normally my sign that it is time to go in. "Knock on wood" no issues yet and have run into grass, and oysters. I need another prop due to the oyster beds. I think maybe you're under powered. I have the 120 on a 20' tidewater.

Sent from my SAMSUNG-SGH-I547 using Tapatalk

Just realized my type-O. I have the 112" shaft 80# thrust.

[speck-chaser]

Originally Posted by Visco

Just realized my type-O. I have the 112" shaft 80# thrust.

You have a 9 ft. shaft on your trolling motor? Not sure Ive ever seen one that long.

[meaux fishing]

Originally Posted by speck-chaser

You have a 9 ft. shaft on your trolling motor? Not sure Ive ever seen one that long.

Lol...that's the new model for offshore boats